歡迎來到Linux教程網
Linux教程網
Linux教程網
Linux教程網
您现在的位置: Linux教程網 >> UnixLinux >  >> Unix知識 >> 關於Unix

最基礎的unix知識


1.2.3 光盤安裝SCO UNIX 5.0.4
安裝操作系統步驟
1)使用軟盤冷啟動,在boot:的提示符後: 回車.
2)接下提示: press to installation: 回車.
3)接下提示:
Press to continue. Press for General help.回車
4)接下提示:
Media device to be used: IDE CD ROM
IDE Controller: secondary (按實際情況修改)
Master or Slave: master (按實際要求修改)
Accept above choices
按兩次向下箭頭,將光標移到: Accept above choices.回車.
5)接下提示:
插入UNIX安裝光盤,選擇OK,回車
6)接下提示:
(選擇鍵盤類型)
Keyboard: US English 回車
7)接下提示:
(注冊系統)
License number: Type in
License code: Type in
Accept above choices
分別輸入注冊號和注冊代碼,然後出現:
License data: Type in
輸入注冊數據後將光標移到: Accept above choices,按回車.
8)接下提示:
Press to continue. Press for install instructions.回車
9)接下提示:
(確認安裝類型)
Upgrade Fresh
選擇Fresh(第一次安裝),回車
10)接下提示:
OK Cancel
選擇OK,回車,繼續安裝
11)接下提示:
(配置基本系統)
System name: scosysv
Security profile: Traditional
Time zone: Eastern Standard/Summer Time
Language: Standard C (English)
Accept above choices
將光標移到: Time zone:按空格鍵,出現提示:
Geographical aiea: North Americal
North Americal time zone: Eastern Standard Time(EST)
Daylight savings time : Yes
Accept above choices
光標移到: North Americal按空格鍵,選擇: Asia回車
光標移到: Eastern Standard Time按空格鍵,選擇: China Standard
Time(CST),回車
光標移到: Accept above choices,回車回到上一畫面
光標移到: Accept above choices, 回車
12)接下提示:
(初始化系統profile)
將光標移到: Accept above choices, 回車
13)接下提示:
(准備硬盤和選擇軟件)
Hard disk setup: UNIX only : Bad Tracking ON
Optional software: SCO OpenServer Enterprise System,241MB
Accept above choices
可修改或接受Bad Tracking ON
將光標移到: Accept above choices, 回車
14)接下提示:
(配置附加軟件)
Network card: Autodetect
Network address: No networking card configured
Video and graphics: IBM VGA
Mouse: No mouse configured
Email system: MMDF
Accept above choices
將光標移到: Accept above choices, 回車
15)接下提示:
(設置密碼)
Root password:
輸入超級用戶密碼,必須牢記,然後出現: 
Please type again to confirm:
再次輸入密碼,以確認
將光標移到: Accept above choices, 回車
16)接下提示:
OK Cancel
選擇OK,繼續安裝
17)接下提示:
Press to continue:
回車
18)接下提示:
Press to continue:
取出軟盤,回車將重新啟動機器,即可正常使用SCO UNIX 5.0.4.
1.2.4外圍設備的安裝
1.2.4.1鼠標安裝
1) #mkdev mouse
屏幕顯示:
Mouse Initialization Program
1.Display current configuration
2.Add a mouse to the system
3.Remove a mouse from system
4.Associate a terminal with an existing mouse
5.Disassociate a terminal from an existing mouse
6.Remove the mouse drivers from the kernel
Select an option or enter q to quit:
2)選2系統會顯示:
The following mouse device types are supported:
1.Serial mouse
2.Bus mouse
3.PS/2-style keyboard mouse (IRQ 12)
Select an option or enter q to return to the previous menu:
3)選3系統會顯示:
The following keyboard mouse device are supported:
1.Low Resolution Keyboard Mouse
2.High Resolution Keyboard Mouse
Select an option or enter q to return to the top level:
4)選2系統會顯示:
Press return when finshed:
5)回車後系統會顯示:
Do you want to use the High Resolution Keyboard Mouse on
any other terminals? (y/n)
6)輸入n,回車,屏幕顯示:
You must create a new kernal to effect the driver change
you specified.
Do you wish ti create a new kernal now? (y/n)
7)輸入y,回車,屏幕顯示:
Do you want this kernal to boot by default? (y/n)
8)輸入y,回車,屏幕顯示:

Do you want the kernal enviroment rebuilt? (y/n)
9)輸入y,回車,屏幕回到主菜單
10)輸入q,退出,重新啟動UNIX,即可在tty02上使用鼠標.
1.2.4.2安裝以太網卡(以3c509為例)
1) scoadmin,回車:
2)選Networks,回車:
3)在Network Configuration Manager 屏幕下,選擇Hardware菜單下的Add
new LAN adapter
4)在 Add new LAN adapter 屏幕下,選擇3Com EtherLink III ISA
(3C509 and 3C509-TP)
5)屏幕顯示:
Do you wish to search for a 3Com EtherLink III ISA
(3C509 and 3C509-TP)?
[ Yes] [ No ] [ Cancel ] [ Help]
選擇 Yes,回車,屏幕顯示:
6)…
[ OK ] [Help]
選擇 OK,回車
7) 屏幕顯示:
I/O Address: |300_______________|v
Interrupt Vector: |10________________|v
Media/Cable Type: |AUTO______________|v

[ OK ] [ Cancel ] [ Help ]
修改Interrupt Vector為9,選擇 OK,回車,屏幕顯示:
8)Please verify adapter is set to the configuration just entered
[ OK ]
選擇 OK,回車,屏幕顯示:
9) HW 3Com EtherLink III ISA (3C509 and 3C509-TP)
- SCO IPX/SPX
- SCO TCP/IP
[ Add ] [ Cancel ] [ Help ]
按方向箭頭將光標移到 SCO TCP/IP,按 Tab 選擇 Add 回車顯示:
10)在 SCO TCP/IP Configuration 屏幕下:
修改 IP Address 和 Netmask. 其余選擇默認值.然後選擇 OK 後屏
幕顯示:
11)[ OK ] [ Help ]
選擇 OK 後回到主菜單
12)在 Hardware 下選擇 Exit 退出.屏幕顯示:
Do you wish to create a new kernal now?
[ Yes ] [ No ]
選擇Yes後屏幕顯示:
13)Do you want this kernal to boot by default? (y/n)
輸入y,回車,屏幕顯示:
14)Do you want the kernal enviroment rebuilt? (y/n)
輸入y,回車,屏幕顯示:
15)Press Enter to continue
輸入回車,重新啟動UNIX,即可.
1.2.4.3並口設置
1)在#號下鍵入:
#mkdev parallel
屏幕顯示:
Do you wish to:
1.Add a parallel port
2.Remove a parallel port
3.Show configuration
4.Help
Select an option or enter q to quit:
2)選擇1後屏幕顯示:
Please select the I/O address for the adapter:
1.Parallel Adapter at address: 378-37f
2.Parallel Adapter at address: 3bc-3be
3.Parallel Adapter at address: 278-27a
4.Other configuration
Select an option or enter q to quit:
3)選擇1後屏幕顯示:
4)Should this port use interrupt (default [7]):
回車,屏幕顯示:
5)Do you wish to create a new kernal now?(y/n)
輸入y後屏幕顯示:
6)Do you want this kernal to boot by default? (y/n)
輸入y,回車,屏幕顯示:
7)Do you want the kernal enviroment rebuilt? (y/n)
輸入y,回車,重新啟動UNIX,即可.
1.2.4.4設置打印機
1)在#號下鍵入:
#mkdev lp 回車
在Printer Manager on scosysv屏幕下選擇Printer菜單下的
Add Local…
2)在Add Local Printer 屏幕下,在 Name:下輸入:lp0; Model: 選擇:
epson. 其余默認.然後選擇 OK.
3)回到主菜單,選擇Host菜單下的Exit,退出
1.2.4.5多用戶卡的設置
1)參照多用戶卡的說明書,按COM2口設置調線.
2)在# 號下鍵入#mkdev serial
3)將光標移到[Add…],回車
4) 選擇第二個Description為4,Ports為4,此時IRQ應為3,
I/O add為1a0,選擇OK回車,屏幕顯示如下:
5)Do you wish to create a new kernal now?(y/n)
輸入y後屏幕顯示:
6)Do you want this kernal to boot by default? (y/n)
輸入y,回車,屏幕顯示:
7)Do you want the kernal enviroment rebuilt? (y/n)
輸入y,回車,重新啟動UNIX.
8)在# 號下鍵入#enable tty2a tty2b tty2c tty2d
Copyright © Linux教程網 All Rights Reserved