前陣子碰到SUSE linux下網卡重命名的問題，是在虛擬機上安裝RAC，通過復制虛擬機後需要完成的。與RedHat linux，以及oralce linux不同的處理方式，下面將其記錄下來，供參考。
1、新節點的網絡配置
#啟動節點之後沒有任何IP配置信息
bo2dbp:~ # ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:174 errors:0 dropped:0 overruns:0 frame:0
TX packets:174 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:11471 (11.2 Kb) TX bytes:11471 (11.2 Kb)
2、使用yast2/newcard刪除之前的網卡，並為新網卡添加IP地址，路由，機器名
#下面是刪除後並配置ip,route之後的信息
bo2dbp:~ # ifconfig
eth3 Link encap:Ethernet HWaddr 00:0C:29:99:DF:0F
inet addr:192.168.7.71 Bcast:192.168.7.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fe99:df0f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:10 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2387 (2.3 Kb) TX bytes:328 (328.0 b)
eth4 Link encap:Ethernet HWaddr 00:0C:29:99:DF:19
inet addr:10.10.7.71 Bcast:10.10.7.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fe99:df19/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1607 (1.5 Kb) TX bytes:238 (238.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:206 errors:0 dropped:0 overruns:0 frame:0
TX packets:206 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13803 (13.4 Kb) TX bytes:13803 (13.4 Kb)
3、停用網路
bo2dbp:~ # rcnetwork stop
Shutting down network interfaces:
eth3 device: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01)
eth3 configuration: eth-bus-pci-0000:02:00.0
eth3 done
eth4 device: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01)
eth4 configuration: eth-bus-pci-0000:02:02.0
eth4 done
Shutting down service network . . . . . . . . . . . . . done